OVH Community, your new community space.

hard drive broken


youwe
22/03/2015, 13h05
Hello,

since two days the Hard Disk is broken. It took 13 hours yesterday until the filecheck was finished. It found tons of errors. Input/Output Error (Code 8) and so on. I even reinstalled the hole system but it remained only 12 hours until all broke again. The drive is broken. So would you please replace the Hard Drive? It is broken. I can't even mount sda3 anymore only sda2 (the root file system).

server id 227685

Rack 80 A12

smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.14.32-xxxx-std-ipv6-64-rescue] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST2000DM001-9YN164
Serial Number: Z1E04FMC
LU WWN Device Id: 5 000c50 03f1d3fe3
Firmware Version: CC4H
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Sun Mar 22 06:56:59 2015 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 584) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 230) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3085) SCT Status supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 082 077 006 Pre-fail Always - 236437896
3 Spin_Up_Time 0x0003 094 094 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 87
5 Reallocated_Sector_Ct 0x0033 072 063 036 Pre-fail Always - 37024
7 Seek_Error_Rate 0x000f 083 060 030 Pre-fail Always - 221909343
9 Power_On_Hours 0x0032 074 074 000 Old_age Always - 22970
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 85
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 1725
188 Command_Timeout 0x0032 100 057 000 Old_age Always - 23 23 71
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 072 055 045 Old_age Always - 28 (Min/Max 24/28)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 84
193 Load_Cycle_Count 0x0032 088 088 000 Old_age Always - 25502
194 Temperature_Celsius 0x0022 028 045 000 Old_age Always - 28 (0 9 0 0)
197 Current_Pending_Sector 0x0012 001 001 000 Old_age Always - 29204
198 Offline_Uncorrectable 0x0010 001 001 000 Old_age Offline - 29204
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 21767h+20m+20.806s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 225078804302
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 24842264437300

SMART Error Log Version: 1
ATA Error Count: 1278 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1278 occurred at disk power-on lifetime: 22970 hours (957 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 01:45:45.855 READ DMA EXT
27 00 00 00 00 00 e0 00 01:45:45.854 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 01:45:45.846 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 01:45:45.824 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 01:45:45.742 READ NATIVE MAX ADDRESS EXT

Error 1277 occurred at disk power-on lifetime: 22970 hours (957 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 01:45:42.803 READ DMA EXT
25 00 08 ff ff ff ef 00 01:45:42.800 READ DMA EXT
25 00 08 ff ff ff ef 00 01:45:42.789 READ DMA EXT
25 00 08 ff ff ff ef 00 01:45:42.789 READ DMA EXT
25 00 08 ff ff ff ef 00 01:45:42.788 READ DMA EXT

Error 1276 occurred at disk power-on lifetime: 22970 hours (957 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 01:44:33.017 READ DMA EXT
25 00 08 ff ff ff ef 00 01:44:33.003 READ DMA EXT
25 00 08 ff ff ff ef 00 01:44:32.991 READ DMA EXT
25 00 08 ff ff ff ef 00 01:44:32.987 READ DMA EXT
25 00 08 ff ff ff ef 00 01:44:32.979 READ DMA EXT

Error 1275 occurred at disk power-on lifetime: 22968 hours (957 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 52 04 00 00 Error: UNC at LBA = 0x00000452 = 1106

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 06 52 04 00 e0 00 00:06:16.689 READ DMA
27 00 00 00 00 00 e0 00 00:06:16.688 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:06:16.680 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:06:16.674 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:06:16.656 READ NATIVE MAX ADDRESS EXT

Error 1274 occurred at disk power-on lifetime: 22968 hours (957 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 51 04 00 00 Error: UNC at LBA = 0x00000451 = 1105

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 51 04 00 e0 00 00:06:13.823 READ DMA
27 00 00 00 00 00 e0 00 00:06:13.822 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:06:13.814 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:06:13.807 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:06:13.782 READ NATIVE MAX ADDRESS EXT

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 3741 -
# 2 Short offline Completed without error 00% 3729 -
# 3 Short offline Completed without error 00% 3729 -
# 4 Short offline Completed without error 00% 3691 -
# 5 Short offline Completed without error 00% 164 -
# 6 Short offline Completed without error 00% 161 -
# 7 Short offline Completed without error 00% 161 -
# 8 Short offline Completed without error 00% 150 -
# 9 Short offline Completed without error 00% 150 -
#10 Short offline Completed without error 00% 132 -
#11 Extended offline Completed without error 00% 3 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay